Soil Investigation in Bali: Coastal Sand, Rice Fields, Volcanic Ground and Limestone

One island, several kinds of ground, and why each plot needs its own investigation.

Bali is a small island, but the ground beneath it changes a great deal from one area to the next. A plot near the beach in the south, a former rice field inland, a valley edge near Ubud and a clifftop on the Bukit peninsula each stand on different material. A foundation that suits one can be wrong for another.

Bali also lies in an active earthquake region. That makes a proper soil investigation more than a formality: it decides the type of foundation, how the structure is designed for earthquakes, and, in some areas, whether the ground can liquefy. This article explains the main kinds of ground in Bali, what the rules now require, and what a good investigation should include.

Four kinds of ground

These are broad patterns from published studies. They help you ask the right questions; they do not replace an investigation of your own plot.

The southern coastal plain. Around Tuban, Sanur, Serangan, Tanjung Benoa and south Denpasar, a study using eight boreholes and 35 cone penetration tests found young sediment about 20 metres thick, lying on limestone.[1] In former lagoon areas it includes very soft, highly plastic clay, from near the surface to about 20 metres deep in places, which is prone to settlement. Along the old beach ridges it includes very loose to loose silty sand, which can liquefy in an earthquake. Groundwater was shallow, from about half a metre to three and a half metres below the surface.[1] A separate study in Pemogan, south Denpasar, found layers between 1.5 and 9.5 metres deep with a critical safety factor against liquefaction.[2] Other coastal areas, such as Canggu and Seminyak, also sit on coastal plains; only an investigation of the plot can confirm what lies beneath.

Former rice fields. Rice fields are kept wet, so the surface layers are usually soft and the water table high. What lies below depends on where the field is: soft lagoon clay near the southern coast is very different from the volcanic deposits under the rice terraces of Gianyar and Tabanan. The fact that a plot was a rice field tells you to investigate carefully; it does not tell you what the ground is.

Volcanic ground in central Bali. Much of central Bali, including the Ubud area, is built on deposits from large eruptions of the Batur volcano, including ignimbrite and tuff.[3] Locally, the hard tuff is known as padas. Volcanic deposits can be strong, but their thickness, weathering and strength vary over short distances, and the river valleys that cut through them have steep sides. They should be tested, not assumed.

Limestone on the Bukit peninsula. Around Jimbaran, Ungasan, Pecatu, Uluwatu and Nusa Dua, the ground is largely limestone, often with only a thin layer of soil above it. Limestone can contain hollows dissolved by water over time. A cone penetration test cannot push into rock, so on limestone the investigation needs drilling with rock cores to show the quality of the rock and any voids below the foundation level.

Earthquakes and liquefaction

The south coast of Bali lies about 100 to 150 kilometres north of the subduction zone where the Indo-Australian plate dives beneath the Sunda plate, and the island has a record of damaging earthquakes, including the 1976 earthquake in Buleleng in the north.[1] The structural design of a house in Bali must therefore follow Indonesia's earthquake design standard, SNI 1726:2019.

Liquefaction happens when loose, water-saturated sand or silt loses its strength during strong shaking and behaves briefly like a liquid. Buildings on it can settle, tilt or crack, and the ground can spread sideways. Three rules matter here:

  • Bali's spatial plan requires a liquefaction risk analysis for development in areas of medium and high liquefaction hazard, including Badung and Denpasar, and building to liquefaction-resistant standards.[4]
  • SNI 1726:2019 places soil that may liquefy in its weakest site class, SF, which normally requires a site-specific analysis.[5] Where the seismic design category of the building requires it, the geotechnical report must evaluate liquefaction, total and differential settlement and lateral spreading, and propose mitigation.[5]
  • The same standard does not recommend shallow foundations on soil with high liquefaction potential, except under specific conditions.[5]

Why good data can save money

SNI 1726:2019 classifies the ground from the top 30 metres, using measured soil properties. If adequate data are not available, the designer must assume a soft-soil class unless there is evidence otherwise.[5] An assumed soft-soil class leads to higher earthquake forces and a heavier structure. A proper investigation can show that the ground is better than the cautious assumption, or confirm that the extra strength is truly needed. Either way, you pay for what your site needs, not for a guess.

What a soil investigation in Bali should include

The right programme depends on the ground, but on most plots it should include:

  • Cone penetration tests for a fast, continuous profile of soft soils and sands; a test with pore pressure measurement (CPTu) gives more detailed data.
  • Boreholes with Standard Penetration Tests and soil samples, so that each layer can be seen and tested in the laboratory. On limestone or hard tuff, rock coring replaces or extends this. The Indonesian geotechnical standard, SNI 8460:2017, covers both soil and rock sampling.[6]
  • Groundwater level, which drives both liquefaction risk and excavation work.
  • A liquefaction analysis in hazard areas, showing the safety factor at each depth and the settlement it could cause.[2][5]
  • Chemical tests of soil and groundwater near the coast, for chloride and sulfate, which attack concrete and steel.[6] Seawater intrusion into groundwater has been reported along parts of the south coast, including Kuta and Sanur.[7]
  • Enough depth. For earthquake design, the site class needs data to 30 metres, and for piles the investigation must continue below the planned pile tips.[5][6] A planned depth is only an estimate. Our practice is that if a borehole reaches its planned depth, for example 30 metres, without reaching the SPT values the engineer has set as the target for a firm layer, it is deepened by a further 10 metres, and again if needed, until that layer is found. Agree a price per extra metre in advance, so the investigation is not stopped at a contract depth before it has answered the question.

We explain the difference between cone tests and boreholes, and why both are usually needed on soft ground, in our article on soil investigation. The same principles apply in Bali.

What to check in the report

  • A plan of the test and borehole locations on your plot.
  • Cone test charts, borehole logs and, where drilled, rock core records.
  • Laboratory results for the soft or loose layers.
  • The groundwater level, and chloride and sulfate results near the coast.
  • The site class for earthquake design, and the depth of investigation compared with the planned foundation.
  • In hazard areas, the liquefaction analysis with its conclusions and recommended mitigation.

The report should then be read by a geotechnical engineer and the structural consultant together, before the foundation is designed. Wherever we build, we advise clients to investigate before designing the foundation, and to add boreholes where the ground calls for them.

Before you get this far, make sure the land itself is right: see our checklist before you buy land in Bali. When the quotes arrive, our guide to comparing contractor quotes shows what to look for. To see how we work, visit how we work.

References

  1. Soebowo, E. (2016). Geologi teknik sedimen Kuarter dan bahaya amblesan, likuifaksi di Serangan-Tuban-Tanjung Benoa, Bali (Engineering geology of Quaternary sediments and subsidence and liquefaction hazards in Serangan-Tuban-Tanjung Benoa, Bali). Jurnal Riset Geologi dan Pertambangan, 26(1), 41-54. DOI 10.14203/risetgeotam2016.v26.279.
  2. Sinarta, I.N. & Basoka, I.W.A. (2019). Journal of Applied Engineering Science, 17(4), 535-540. DOI 10.5937/jaes17-20794 (liquefaction potential from CPT data, Pemogan, South Denpasar).
  3. Sutawidjaja, I.S. (1990). Evolution of Batur caldera, Bali, Indonesia. Thesis, Victoria University of Wellington.
  4. Bali Provincial Regulation No. 2 of 2023 on the Bali Provincial Spatial Plan 2023-2043 (Peraturan Daerah Provinsi Bali Nomor 2 Tahun 2023), Article 105(8).
  5. Badan Standardisasi Nasional (Indonesian National Standards Agency). SNI 1726:2019 Tata cara perencanaan ketahanan gempa untuk struktur bangunan gedung dan nongedung (Earthquake resistance design for buildings and other structures). Clauses 5.1 and 5.3.1 (site classification, site class SF); 6.7.2 and 6.7.3 (geotechnical investigation and liquefaction); 7.13.8 (foundations on liquefiable sites).
  6. Badan Standardisasi Nasional. SNI 8460:2017 Persyaratan perancangan geoteknik (Geotechnical design requirements). Clauses 5.3 (soil, rock and groundwater sampling, including 5.3.5 rock) and 5.5.4 (chemical tests on soil and groundwater).
  7. The Jakarta Post (20 November 2009). Bali warned of clean water crisis.

Frequently asked questions

Do I need a soil investigation to build a villa in Bali?

Yes. The ground in Bali varies from soft coastal clay and loose sand to volcanic tuff and limestone, and the foundation and earthquake design depend on it. In medium and high liquefaction hazard areas, including Badung and Denpasar, Bali's spatial plan also requires a liquefaction risk analysis.

Which parts of Bali are at risk of liquefaction?

Bali's spatial plan lists medium and high hazard areas in Jembrana, Badung, Denpasar, Klungkung, Karangasem and Buleleng. Studies in the south have found liquefiable sandy layers at Serangan, Tanjung Benoa and Pemogan, where groundwater is shallow. Only an investigation of the plot can confirm the risk.

Is a cone penetration test enough in Bali?

On soft coastal ground it is a useful first step, but boreholes with sampling and laboratory tests are usually needed as well. On limestone or hard tuff, a cone test cannot penetrate, so rock coring is used instead.

How deep should a soil investigation go in Bali?

Indonesia's earthquake standard classifies the site from the top 30 metres of ground, and for piles the investigation must continue below the planned pile tips. If the target SPT values have not been reached at the planned depth, the borehole should be deepened, for example 10 metres at a time, until a firm layer is found. On rock, coring should go deep enough to confirm sound rock below the foundation.

Plan it right from the start

Tell us where your land is, its size, your architect or consultant (if you have one), and when you plan to start. Our team will review it and get back to you.